Dake V-16 Instrukcja Obsługi

4/11/2007 1 DAKE / JOHNSON VERTICAL BAND SAW Model F - 16 INSTRUCTION MANUAL Need band saw blades? Call Dake DAKE (Division

4/11/2007 10 MATERIAL SHAPE MATERIAL SHAPE MATERIAL SHAPE MATERIAL IN INCHES TOOTH SELECTION TOOTH SELECTION TOOTH SELECTION 0 14 / 18 14 /

4/11/2007 11Machine Operation Look over the control panel to get familiar with the buttons before operating (see picture below). Digital Tachom

4/11/2007 12MACHINE OPERATION To operate the machine, do the following: 1. Turn the main power on, and then push the saw power button. 2. Now t

4/11/2007 13 ACCESSORIES Rip Fence Part number 81521 PROTRACTOR HEAD See figure 4 part number 75561 T-SLOTS T-slots are machined into the wor

4/11/2007 14 How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced) 1. Press an

4/11/2007 15 PARTS BREAKDOWN AND PARTS LIST

4/11/2007 16 Figure 1.1 ITEM PART NAME PART NO. F-16 1 Hand wheel 81529 1 2 Adjusting Wheel Collar 81530 1 3 Spindle 81532 1 4 Crow

4/11/2007 17 Tracking band wheel assembly 1.2 Figure 1.2 ITEM PART NAME PART NO. Complete Assembly 716501 1 1 Screw 8mm x 10mm 81571

4/11/2007 18 Figure 2.1 ITEM PART NAME PART NO. V/E-16 1 Table Insert (Left Rear) 81597 1 2 Table Insert (Right Rear) 81598 1 3 Table Inse

4/11/2007 19 Lower Wheel assembly 3.7 ITEM PART NAME PART NO. V/E-16 1 Band Wheel Cover – Sold as 714834x 80540 1 2 Band Wheel Casting 80

4/11/2007 2 WARNING! This machine must be wired by a qualified electrician. This machine is designed to be wired for the specified voltage with a to

4/11/2007 20 Blade guard assembly 4.6 Blade guard assembly 4.6 Item # Part # Part Description Qty. 3 81926 Brus

4/11/2007 21 Blade Guide Assembly 4.8 Item # Part Name Part # Qty. 1 Cap Screw 81781 2 2 Blade Guide Holder 81935 2 3 Set Screw 81936 2

4/11/2007 22 Item # PART NAME PART NO. Qty 1 Gear box 301663 1 2 Motor Single Phase and 3 phase 301665 1 3 Digital read out 301832

4/11/2007 23 Items not shown on gear box assembly Washer 70270 2 Bolt 81505 2 Shaft 87121 1 Bearing 301810 1 Outboard Support 871

4/11/2007 24

4/11/2007 3 Machine Features F - 16 WARNING!!! The machine table must NOT be used as a lifting point. Damage to the saw could occur. UNLOADING: Re

4/11/2007 4 protective coating on machined metal surfaces. These surfaces should be cleaned with the appropriate solvent and then coated with a light

4/11/2007 5 ELECTRICAL: To wire this machine there is a small box on the back side of the machine, this is where the machine is wired in (see illu

4/11/2007 6 To change the machine from 1 phase to 3 phase follow the instructions below. 220 Volt 1 Phase How to wire for 220 Volt 1 Phase: 1.

4/11/2007 7 WARNING!!! Electrical supply must be locked out when changing the blade. Blade selection is based on the many factors and complexity of

4/11/2007 8 BLADE TENSIONING The blade indicator is located inside the upper wheel compartment, on the lower left side of the idle wheel. (See pictu

4/11/2007 9 The blade should always be inspected before installing on the machine. Things to look for should be the smoothness on the sides and ba